Quicksilver 817019A2 MerCruiser Stern Drive Trim Valec prívesné svorky, sada 2 kusov

Brand:‎Quicksilver

3.8/5

72.94

MerCruiser Stern Drive Trim Cylinder Trailers klipsy 817019A2 sa ľahko nacvaknú na oba valec trim, aby podporili upravený pohon pri ťahaní lode. Sú vyrobené z jasne červeného/oranžového kompozitného plastu, aby vám pripomenuli, aby ste ich pred spustením člna odstránili. Značka Quicksilver je lídrom v dodávaní nekompromisných motorových olejov, dielov a príslušenstva pre námorný priemysel už viac ako 65 rokov. Quicksilver je popredným dodávateľom náhradných dielov motorov, olejov a príslušenstva Mercury Marine Original Equipment, ale tiež pracuje tak, aby slúžil všetkým značkám originálneho vybavenia v námornom a silovom priemysle. Získala si lojálnych nasledovníkov poskytovaním produktov najvyššej kvality, ktoré sú testované v tých najprísnejších prostrediach a testovacích postupoch. Žiadna popredajná spoločnosť sa nepribližuje k úrovni výskumu a dizajnu ako Quicksilver; Nákup Quicksilver znamená nákup výkonu, ochrany a pokoja.

Vyrobené tak, aby spĺňali špecifikácie výrobcu originálneho vybavenia Mercury Marine, aby sa maximalizoval výkon vášho prívesného motora Mercury a Mariner alebo zadného pohonu MerCruiser. Dva klipy v balení. Vyrobené z jasne červeného/oranžového kompozitného plastu. Upevnite na orezávacie barany valca, aby ste podporili orezaný pohon pri ťahaní lode.
Brand Name ‎Quicksilver
Color ‎Unspecified
Customer Reviews 4.7 4.7 out of 5 stars 305 ratings 4.7 out of 5 stars
Fishing Technique ‎Spinning, Casting
Included Components ‎2 trailering spacers
Item Dimensions LxWxH ‎15.5 x 4 x 1.5 inches
Item Package Dimensions L x W x H ‎14.9 x 4.2 x 0.3 inches
Item Weight ‎0.01 Ounces
Manufacturer ‎Quicksilver
Material ‎Various Materials
Model Name ‎817019A2 MerCruiser Stern Drive Trim Cylinder Trailering Clips, Set of 2
Number of Items ‎1
Package Weight ‎0.46 Kilograms
Part Number ‎817019Q2
Size ‎Unspecified
Suggested Users ‎Unisex-adult

3.8

8 Review
5 Star
83
4 Star
10
3 Star
3
2 Star
2
1 Star
2

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené*

Scritto da: Craig
Must if you trailer your boat
I had to cut mine for my alpha 1 Gen 2 but a quick run across my table saw and it fit fine. You could use any saw but my hands are as steady as M.J. Fox’s so I need more stable tools.
Scritto da: Carleyjo75
Great for traveling
These are great to support the boat motor while traveling BUT u need something to strap them on they won’t just stay on while traveling
Scritto da: Amazon Customer
Great product!
Though it may not be an essential towing accessory, I’d rather be safe than sorry. I opted to cut the rounded tabs off to make it easier to remove when hydraulic pressure is removed. Clips onto hydraulic arms well and doesn’t easily remove when freed up from pressure. If you’re overly cautious like myself, I definitely recommend this product. Pictured on 2000 Glastron gX205 with Alpha One out drive.
Scritto da: Alan Bailey
Exactly what I needed
This is exactly what I needed for my boat. Perfect fit, high quality.
Scritto da: Dale
A must for any trailered boat with Mercruiser stern drive
Lift ram supports are chunky and made of a dense plastic. Cut them down to size, for specific application Bravo 1 with anodes on rams, as per the instructions on the back of the packaging. They clip on firmly and will prevent the drive from hitting the road in the event of a hose bursting or a ram seal failure while boat is on towed trailer.
Scritto da: A Likely Story
Simple solution
1995 Alpha I Gen II - Ignore the chart they include, remember your cylinder anodes (which take all the load), put outdrive to trailering height and measure. Left mine a little long to the mark and used a chopsaw for simple cutting. Holes drilled for safety lanyards will be cut off when shortening length by very much - drill after you get length/exact tethering config. Paracord makes a great tether but you might need to bungee them as the molded profile isn't as tight on the cylinder rod as hoped. Care s/b taken to not over-retracting the pneumatics after bottoming on clips. Should have done this years ago. Can't imagine a situation where these wouldn't be as good/better than running on the cylinders and for the price?
Scritto da: J. Schenck
Great fit! Even better piece of mind!
They may seem somewhat expensive, 100% worth it! These fit really well on the Alpha one (gen 2 with anode's on the arms). I cut them to length then cleaned up the cut with some sanding with a sanding block. click them in place then put some pressure down on them with trim. Now I can travel without worrying about the outdrive working its way down and hitting the street (yikes!) - this is way cheaper than a strike against the outdrive! Every boat should have these on when transporting!
Scritto da: Scott
Fit good
Have to cut down to size. Other than that they fit good

Súvisiace produkty

Objavte našu medzinárodnú sieť

Dodávame do 28 krajín, viac ako 200 000 produktov. Zostaňte informovaní, prihláste sa na odber noviniek.

Array