HHIP 1011-6004 0-80NF H2 Špirálová zástrčka s 2 drážkami 0-80NF Veľ.

Name: HHIP 1011-6004 0-80NF H2 Špirálová zástrčka s 2 drážkami 0-80NF Veľ.
Brand: HHIP
SKU: 0076905300132
Price: 24.29 EUR
Availability: InStock

Brand:HHIP

3.4/5

€
24.29

0-80NF H2 2-zubý závitník so špirálovým hrotom ~ brúsený závit. ~ Zem z pevného materiálu. ~ Rýchlorezná oceľ.

Nie sú k dispozícii žiadne jednotky

EAN: 0076905300132

Kategórie Priemysel a veda, rezné nástroje, Závitníky, Špirálové hrotové závitníky,

Hmotnosť balíka: 0,009 kg. zemný závit; Zem z pevného. Veľkosť 080NF; H Limit/Flute H-2/2. Vysokorýchlostná oceľ.

Item model number	1011-6004
Manufacturer	HHIP
Product Dimensions	3 x 1 x 6 inches; 0.32 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené^*

Vaše hodnotenie

Scritto da: E. Burdick

Accurate, tough, good spiral point, good for aluminum. Very inexpensive.

This is a solid tool. The two flute spiral point makes tapping aluminum pretty easy. This is a tiny tap, and tapping any depth of hole at this size is tough with a lower quality tap. The two flute configuration makes room for chips and the spiral point pushes them out of the way through the hole. I normally hand tap this size in the drill press with a centering jig or with a tapping guide to keep the tap handle straight and in line with the hole. Note the correct tap drill size (#50) is critical.

Scritto da: Ian Mazursky

Works

This is a good 2-56 tap. Ive used it in aluminum and it worked great.

Scritto da: Anthony_atp

Handy tool

I used this to tap threads in plastic and hardboard on model railroad rolling stock for 2-56 screws. I don’t have a tap 50 drill but used 1/16 inch with good success. The screws went in tight. I have not used this device on metal yet. However I would probably use a 5/64 inch drill bit to reduce stress when tapping the thread. Turn the tap with care, use oil for lubrication and don’t forget to reverse the movement regularly to clear the metal debris from the cutting edge.

Scritto da: Janette Cherba

Worked well

Used it to tap holes in 3/32 inch thick mild steel (had it chucked in a drill press & turned by hand). It worked well and based on its construction it appears sturdy. It would have been nice to have it within the plastic container it was shipped with, rather than rolling around in the small ziplock baggie. The plastic container is a nicety.

Scritto da: Amazon Customer

Wrong item shipped in package labeled as what was ordered.

Package contained a metric M2-6H tap. Not even close to a 12-28NF SAE, which is almost 3 times the diameter. Bought the proper one at Tractor Supply, which also included a 1/4-28NF tap for almost the same price.

Scritto da: John Smith

Works great on small titanium pieces

I know this isn't rated for tapping titanium but the spiral end makes it ideal for small titanium jobs. So far I've only hand-tapped two or three quarter-inch pieces and had zero problems. I used Tap Magic as my cutting fluid and even though it's not the best for titanium it also performed perfectly.

Scritto da: BN2Wild

It works!

It works, what else do you need to know???

Scritto da: IamtheWB

Very Precise and Strong enough Tap. I use it ...

Very Precise and Strong enough Tap. I use it on Titanium Grade 2 (2mm) with a #55 drill bit.

Scritto da: chris

Works good so far.

Good little tap for the money however I should have purchased a 2 fluted tap for my hotwheels cars.

Scritto da: jamie templeton

Works well

Worked great for putting a pocket clip on my buck 112.