Drill America - DWTET12X3/8-16 3/8-16 x 12 Vysokorýchlostný závitník s oceľovou kladkou, séria DWT DWTET12X3/8-16 3/8-16 12 dlhá

Name: Drill America - DWTET12X3/8-16 3/8-16 x 12 Vysokorýchlostný závitník s oceľovou kladkou, séria DWT DWTET12X3/8-16 3/8-16 12 dlhá
Brand: Drill America
SKU: 0887861080040
Price: 73.51 EUR
Availability: InStock

Brand:Drill America

3.5/5

€
73.51

Pre pevný držiak navijaka budete musieť pridať nosič navijaka Warn Trans4mer. Kompatibilné s: PowerPlant HP a HD, Endurance 12.0, VR12, ZEON, VR10, 9.5cti, 9.5xp, XD9i, XD9, M8, VR8, M6. Vyrobené z čiernej práškovo lakovanej ocele. Skrutky priamo do krytu mriežky.

Suma

Pridať do košíka Kúpte teraz

EAN: 0887861080040

Kategórie Priemysel a veda, rezné nástroje, Závitníky, Frézovacie závitníky,

Pravostranné rezné nástroje majú rezací mechanizmus, ktorý sa aktivuje, keď sa pohybujú v smere hodinových ručičiek. Okrúhle so štvorhrannou stopkou. Nepovlakované nástroje majú len základný substrát bez akejkoľvek ďalšej úpravy alebo povlakov a sú vhodné pre širokú škálu aplikácií. Nástroje z rýchloreznej ocele sú vhodné pre väčšinu aplikácií na všeobecné použitie a ponúkajú kombináciu tvrdosti a húževnatosti pre odolnosť proti opotrebovaniu. Predlžovací kohútik slúži na závitovanie nábojov remeníc pre olejové uzávery alebo nastavovacie skrutky. Dlhá stopka je tiež ideálna na dosiahnutie otvorov neprístupných so štandardnými dĺžkami závitníkov.

Item model number	DWTET12X3/8-16
Manufacturer	Drill America
Package Dimensions	12.05 x 0.75 x 0.71 inches; 6.35 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené^*

Vaše hodnotenie

Scritto da: Tom Gentry

Great value!!

Cut fast and was strong

Scritto da: GEBrown

Good tap, but not for deep holes

I ordered this tap because I needed to thread deep (6") into a wood hole. However, the shaft on this tap is about 21/64", just a hair larger than 5/16", so it is not good for the purpose I bought it. But it did seen well made and useful if you needed to reach a long distance. Just wanted to alert others that might want to use it for the wrong purpose as I did. I returned it with no problems. FYI

Scritto da: Centropomus Robalito

Perfect for Tapping an AR Bolt Release roll pin hole.

I don't like roll pins on AR lowers so I will use the appropriate tap drill and tap for the 6-32 pins that Aero Precision provides for their M4E1 lowers. This tap allows you to reach behind the rear lower for full rotation and better alignment. I've used it at least half a dozen times and still sharp; I use cutting lubricant even though it cuts aluminum like butter. I cut almost all the way and use the screw to swage the last thread or two for a tight fit.

Scritto da: Skyhawk

Drill America = Made in China

The image shown is for the correctly designed American made tap. The American made version would allow you to make deeper tabs. The one that I received made in China and has a larger shaft diameter which prevents tapping deeper holes. McMaster here I come.

Scritto da: The Honest Critique

How To Fix This Incorrect 3/8"-16 Tap

The photo for this tap shows an undercut extended tap. But the tap you get is not undercut. Therefore this tap cannot tap any deeper than a standard length tap! I didn't have the time to return this incorrect tap so I decided to fix it. I put the tap in my drill press and turned it on. Then I took a a flap disk sander and ground the shank of this tap down to .300. It only took a minute or two. Now I can tap entirely thru a 2" long rod of 6061T6 aluminum.

Scritto da: GJ New York

Works

I used it to tap threads into aluminum. Worked fine.

Scritto da: VERY Satisfied

Easy to deal with

worked fine

Scritto da: Web

Good Product

Good product. Tapped the hole I worked on with ease.