Závitová vložka E-Z LOK pre plastové kužeľové jednolopatkové mosadzné vložky so závitom 1/4-20 (balenie 10 500 Počet spolu) 2000

Name: Závitová vložka E-Z LOK pre plastové kužeľové jednolopatkové mosadzné vložky so závitom 1/4-20 (balenie 10 500 Počet spolu) 2000
Brand: E-Z LOK
SKU: 0847554043585
Price: 154.22 EUR
Availability: InStock

Brand:E-Z LOK

3.9/5

€
154.22

Závitové vložky E-Z Sonic pre plasty Ultrazvukové závitové vložky E-Z Sonic pre plasty sú dostatočne odolné pre najnáročnejšie prostredia a dostatočne všestranné, aby vyhovovali potrebám akejkoľvek aplikácie s vynikajúcim krútiacim momentom a odolnosťou proti vytiahnutiu. Mosadzné závitové vložky sú určené na vkladanie štandardných strojových závitov do 3D tlačených a termoplastických dielov. Nainštalujte tieto kovové závitové vložky ultrazvukom alebo pomocou tepelného pohonu. Kónický dizajn zjednodušuje inštaláciu. Dostupné s kužeľovými závitovými vložkami s jednou a dvojitou lopatkou, rovnými závitovými vložkami v zapustenej alebo prírubovej konfigurácii. Vlastnosti * Kužeľové a rovné konštrukcie * Inštalácia ultrazvukom alebo pomocou tepelného pohonu * Kužeľový dizajn v jednej a dvojitej lopatke

Suma

Pridať do košíka Kúpte teraz

EAN: 0847554043585

Kategórie Priemysel a veda, Hřebíky, Skrutky a spojovací materiál, Nutky, Vložky do matíc,

JEDNODUCHÉ SILNÉ ZÁVITY – Vysokokvalitné mosadzné závitové vložky sú dostupné s palcovým aj metrickým závitom. DOSTUPNÉ ŠTÝLY – Kónické vložky E-Z Sonic sú dostupné v konfiguráciách s jednou alebo dvoma lopatkami, aby vyhovovali vašim požiadavkám na hrúbku materiálu. NA POUŽITIE S APLIKÁCIAMI – Závitové vložky pre plasty sú určené na vkladanie štandardných strojových závitov do 3D tlačených a termoplastických dielov. JEDNODUCHÁ INŠTALÁCIA – Nainštalujte tieto kovové závitové vložky ultrazvukom alebo pomocou tepelného pohonu. Kónický dizajn zjednodušuje inštaláciu. ZÁVITOVÉ VLOŽKY PRE PLASTY – Ultrazvukové závitové vložky E-Z Sonic pre plasty sú určené na montáž do termoplastov po lisovaní.

Brand	E-Z LOK
Color	Plain
Country of Origin	Taiwan
Item Dimensions LxWxH	7 x 3 x 2.5 inches
Item model number	TH-420-SV
Manufacturer	E-Z LOK
Material	Brass
Product Dimensions	7 x 3 x 2.5 inches; 2.6 Pounds
Size	One Size

5 Star

4 Star

3 Star

2 Star

1 Star

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené^*

Vaše hodnotenie

Scritto da: Kindle Customer

Great insert, holds well in wood if you do it right. The insert I used was 1/4-20 15/16 long

I did a test where I drilled the recommend hole and pressed in one insert into some maple and I moved over 3 inches and put some 5 minute epoxy in between and a light film on the knurl. I pressed this in and let it cure for 3 days. I inserted a 1/4-20 hex head bolt in 2" long and tightened the bolt down slowly. The insert held fairly well at first but eventually pulled right out. I moved over the in insert with the epoxy on it and I turned the bolt down and it started to get fairly stiff to turn. I kept turning and then I heard a pop and the thought that the insert came lose. No, it was the back side of the 1" maple creaking out as I screwed it down. The flat ended bolt split the maple about 3 inches before I saw any of the bolt. The insert is still in the board as strong as the day I put it in the male hole. There great insert and I feel that under the right circumstances and installation Technic will work very well in wood and not just plastic. Ten wahoo's the the folks who designed this insert. Great job!

Scritto da: Bob Tobias

Works great on 3D prints and you may not even need a special tool!

The outside diameter of the top of these inserts, the end you press against, is 9.6mm. That's a tad wider than my soldering iron with its tip removed. I can set them perfectly without using any special-purpose soldering iron tips. I still use the 6mm tip from myShineNow Heat-set Insert Tips because I have them anyway. And, as long as we're talking dimensions, the inserts are 7.6mm long. You will, of course, want to make sure you are putting them into something at least that thick. Also, the diameter of the bottom end, the end that goes into the plastic first, is 9mm, should that be useful to your design.

Scritto da: DarkMavrik

works well

I just use a regular soldering iron to push these into place, works great go through about 100 a month with all the stuff I do and haven't had one fail yet

Scritto da: KMan

Great For 3D Printed Camera Accessories

I've 3D printed a few camera accessories such as tripod adapters and used these. They're the perfect length for standard tripod screws.

Scritto da: Lisa H.

Good quality

Use a lot for various 3D printing projects

Scritto da: Aerial-Pixel

These Excellent for 3D Prints

The media could not be loaded. These are perfect for installing 1/4-20 threads in 3D prints, love them. To install I just use a soldering iron @ 380C and press them in place. I've purchased them several times with no issues.

Scritto da: Nick

Works great for my 3d prints

I have used most of the pack at this point and am very happy with the quality.

Scritto da: ElllisGL

They work as expected.

I used this for a 3D printed camera quick release and it still in place.