Súprava vŕtačiek/závitníkov/záhlbníkov, Sae, súprava 6 kusov 6-32 až 1/4-20

Name: Súprava vŕtačiek/závitníkov/záhlbníkov, Sae, súprava 6 kusov 6-32 až 1/4-20
Brand: Greenlee
SKU: 783310176206
Price: 72.72 EUR
Availability: InStock

Brand:Greenlee

3.8/5

€
72.72

POPIS PRODUKTU Súprava vrtákov/závitníkov/záhlbníkov, smer rezu vpravo, SAE, počet kusov 6, vysokorýchlostná oceľ, povrch bez povrchovej úpravy, typ stopky 1/4 palcov. Šesťhranná skrutka na rýchlu výmenu, zahrnuté veľkosti 6-32, 8-32, 10-24, 10-32, 12-24 a 1/4-20, vrátane plastového puzdra a adaptéra na rýchlu výmenu AMAZON.COM Pohľad na vŕtačku zväčšiťZobraziť na vŕtačku zväčšiťPohľad na protizub väčší Jeden bit, ktorý robí to všetko. Vŕtanie, závitovanie a zahlbovanie v jednej operácii. Kombinované bity Greenlee na vŕtanie, závitovanie a zahlbovanie – všetko s jedným bitom. zobraziť väčší Kombinované vrtáky/vrtáky Greenlee sú vysokokvalitným riešením, keď potrebujete rýchlo a presne vyvŕtať, závitovať a zahĺbiť dieru. Predtým ste na vytvorenie závitového otvoru museli vykonať tri samostatné operácie, z ktorých každá vyžadovala vlastný nástroj: vrták, závitník a zahlbovací nástroj. Kombinované bity Greenlee vykonávajú všetky tri operácie s jedným bitom a poskytujú vám rovnakú presnosť a výkon v jednoduchom, rýchlom a ľahko použiteľnom balení. Súčasťou balenia je aj adaptér na rýchlu výmenu, ktorý vám pomôže vŕtať, závitovať a zahlbovať a dokonca ešte rýchlejšie zasúvať upevňovacie prvky. Kombinované bity Greenlee umožňujú použitie s mäkkou oceľou s hrúbkou až 10 gauge, takže vŕtanie, závitovanie a zahlbovanie otvorov je rýchlejšie a jednoduchšie ako kedykoľvek predtým. Vrátane kufríka pre jednoduchú prepravu a skladovanie. zobraziť väčšie NAJLEPŠIE * Vŕtanie, závitovanie a zahlbovanie v jednom rýchlom a jednoduchom úkone * Rovnako presné a podstatne rýchlejšie ako pri použití štandardných vrtákov, nástrojov na závitovanie a zahlbovanie * Konštrukcia z tvrdenej vysokokvalitnej nástrojovej ocele na použitie v kove s hrúbkou až 10 * Zadná strana skosená, aby sa zabránilo poškodeniu nadmerným vŕtaním * Silná šesťhranná stopka zaisťuje pevné spojenie s vrtákom * Súčasťou balenia je rýchlovýmenný adaptér na jednoduché prepínanie bitov VRÁTANÉ KOMPONENTY Skonštruované na vŕtanie, závitovanie a zahlbovanie do mäkkej ocele s hrúbkou až 10, Greenlee DTAPKIT sa dodáva s nasledujúce veľkosti:zobraziť väčšie Číslo modelu Popis DTAP6-326-32NC Vrták a závitník DTAP8-328-32NC Vrták a závitník DTAP10-2410-24NC Vrták a závitník DTAP10-3210-32NF Vrták a závitník DTAP12-2412-24NC Vŕtačka a závitník DTAP1/4-201/4-20NC vrták a závitník Kompaktné plastové puzdro a rýchlovýmenný adaptér sú tiež súčasťou balenia. Náhradné a extra bity sa predávajú samostatne. K dispozícii je aj súprava metrických vrtákov a závitníkov. (Model DTAPKITM KIT) O GREENLEEFG Greenlee, ktorý bol založený v roku 1862, je lídrom, pokiaľ ide o vývoj inovatívnych nástrojov pre profesionálnych obchodníkov. Od začiatkov výroby sudov až po súčasný výber nástrojov na inštaláciu drôtov/káblov, elektronických testovacích a meracích prístrojov a iných riešení je Greenlee naďalej rešpektovaným a dôveryhodným zdrojom nástrojov pre profesionálov aj nadšencov. Bez ohľadu na to, aké nástroje potrebujete, vždy sa môžete spoľahnúť na Greenlee, že vaša práca bude rýchlejšia, bezpečnejšia a jednoduchšia. OD VÝROBCU Kompletné vŕtanie otvorov, rezanie závitov a odihlovanie/zahlbovanie v jednej operácii pomocou elektrickej vŕtačky šetrí prácu a čas. Zadná strana skosená za závitníkom, aby sa predišlo poškodeniu závitu prevŕtaním. Odihlovač/zahlbovač sa dodáva aj na hrote za zadným kužeľom. Vyrobené z kalenej rýchloreznej ocele vs. uhlíkovej ocele pre dlhšiu životnosť. Vysoko kvalitná šesťhranná stopka na zaistenie pevného spojenia so skľučovadlom. Navrhnuté na poklepanie na kov do hrúbky 10. Vrátane rýchleho výmenného adaptéra a puzdra. Pozrieť viac

Nie sú k dispozícii žiadne jednotky

EAN: 783310176206

Kategórie Nástroje a domáce potreby, Elektrické a ručné náradie, Nástroje a príslušenstvo k elektrickému náradiu, Nástroje a príslušenstvo pre vŕtačky, Brity na zahlbovanie, Vrtačky Vrtáky,

Elektrické rezanie a pílenie. Krajina výroby: Čína. Výrobca: Greenlee.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Greenlee
Brand	‎Greenlee
Color	‎Green
Country of Origin	‎China
Customer Reviews	4.7 4.7 out of 5 stars 1,270 ratings 4.7 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Finish	‎Steel
Finish Type	Steel
Finish Type	‎Steel
Included Components	‎Unit^Instruction Guide
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	10 x 10 x 12 inches
Item Dimensions LxWxH	‎10 x 10 x 12 inches
Item model number	‎DTAPKIT
Item Package Quantity	‎1
Item Weight	‎0.64 ounces
Manufacturer	‎Greenlee
Material	High Speed Steel
Material	‎High Speed Steel
Measurement System	‎Inch
Part Number	‎DTAPKIT
Product Dimensions	‎10 x 10 x 12 inches
Shank Type	Hex
Shank Type	‎Hex
Size	‎6-32 to 1/4-20
Style	‎Set
Surface Recommendation	‎Alloy Steel
Thickness	‎11 Inches
Tool Flute Type	‎Straight
Tool Tip Description	‎Split point with web thinning
Warranty Description	‎1 year manufacturer

5 Star

4 Star

3 Star

2 Star

1 Star

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené^*

Vaše hodnotenie

Scritto da: WAVet

Game changer!

This self tapping drill bit set has allowed for me to stop wasting precious time and producing beautifully threaded screw holes. We love them so much, we bought a second set. Get these, you will not be sorry!

Scritto da: ajacksonian

A good combo set for when you don't need indexed bits, taps and countersinks

I've been using these to drill and tap holes in mild steel plates for electrical distribution boxes that I have I am using for something other than circuit breakers. This has meant using the mid-range of these taps: 10-24, 10-32 and 12-24. I will have future use for the others and am also purchasing the next to sizes up to add to this case. Using a power driver (Milwaukee 12v lithium) has allowed me to get through the mild steel with use of cutting fluid in relatively short order. Threading using a power driver takes a lot of patience and some skill, and if you have any scrap metal to practice on, I advise you to do so first as you can easily strip out threads with a driver. In fact what I have done is go to a ratcheting hand driver that accepts hex bits, and then hand tapping after I get the initial hole drilled (stopping at about 1/3 the way up where the first threads appear on the bit). Once through hand tapping is more reliable for me and with cutting fluid and cleaning after each and every hole with a phosphor-bronze brush to remove material from the threads, I've been able to speedily put in a good dozen threaded holes in a bit less time than it took me to do it via separate drilling and tapping (although the tapping was done with a cheap, low-end set of taps that finally saw the target ones I use the most no longer able to do much). Patience and being mindful of the state of the threading, backing out when necessary to clean the bit, and then slowly going in again to finish the job is something I'm used to and having these taps on a hex bit has been a huge help. I haven't found this set to be more brittle than single taps, and they appear to wear a bit better than the cheap blue box set I picked up for the occasional job, here and there. Even with thread cleaning of the tap and tapped hole, that first screw in seems to find a bit more in the way of particulates than I would like: somewhere some fine particles aren't being removed well. The actual holes are just a bit loose, but that isn't a worry given the application on relatively thin plate and sheet steel, as the threads just need to hold and that they do just fine. PROs - A good range of taps for electrician's work - Good cutting rate for the drill section, use cutting fluid - Nice taps and remember the basics of moderate application of force and backing out to clean threads CONs - A bit pricey, that is to be admitted and that is why the one star goes - Use a good nylon tube brush to clean threaded holes, as fine particles get left behind In all a decent set of combination drill/tap/countersinks. If you already have a decent tap set, then you probably won't need these unless it is to put into a toolbox to take out on a job for quickie threading. This set is perfect if you are doing a few holes for electrical work or just need to get something put in and don't have access to a full set of indexed drill bits and taps. Worth buying! The metric set is just to expensive for my blood, though, so have to do that on the piecemeal basis for awhile more.

Scritto da: Toolman

Best tap set I have ever used

This is a very good tapping bit set. It is insanely durable. I used this in an application where I needed to tap out a ton of structural columns in an old building using the 1/4-20 tapping bit. 1/3 of the columns were 1/4" thick, 1/2 of them were 3/8" thick and the rest were 1/2" thick. This bit got through them all with absolutely no problems. Of course for the thicker ones I had to pre drill with a 13/64 drillbit but that is expected when the tip on this is only so long before the thread cutters start. As long as you use plenty of oil and reverse to break the chips a lot this will not break on you. I am in disbelief at how much better it performed compared to how it is advertised. they say it will only do 1/8" but with a predrilled hole it will do up to 1/2" of structural steel! I think the people who complained it broke were using it incorrectly. If you don't go in straight then of course it will break, like any tap.

Scritto da: Yoelvis Garcia

La mejor oferta

The media could not be loaded. A la tortuga le agrado

Scritto da: Charles W.

Great Tap Set for Portable Drills

This is a set of drill/tap for common SAE machine screws. They have a 1/4" hex base for a speed-lock adapter in your drill - Or you could use them directly in the chuck. I use this to tap brass and aluminum. It works great! Although it is a drill and tap bit in one, I strongly reccomend drilling a pilot hole if you are working with anything other than sheet metal. Just pick a bit about the size or very slightly smaller than the drill section of this bit and pilot the hole with that. The thickest I have tapped is 1/2" brass bar. I use a battery powered drill with torque limiting settings when I use this bit. It helps to apply WD-40 or cutting oil to the bit before each use. The base of the tool exactly fits my drill's 1/4" hex speed lock adapter. Keep the drill aligned correctly, and do not over-torque. If you are tapping very deeply, you may need to back out a bit to clear shavings before completing the tap. The good: 1/4 inch speed lock base, tap with your portable electric drill, threads fit well, great quality. Case contains the common SAE screw thread sizes. The bad: I cannot think of anything.

Scritto da: onys arabitg

Muy buena compra

Muy buenas muy durables

Scritto da: Amazon Customer

Great for making panels

I use these at work all the time and they're awesome for making panels! Much cleaner look!

Scritto da: Jackofalldave

Great for 1/4” or less metals

Works well. This set is not designed to drill and tap through metal heavier/thicker than 1/4”. And always use some type drilling/tapping liquid. It cools the bit and provides lubrication. Work well for me so far.

Scritto da: gameoso

Inservible y sin garantía

Desconozco cómo funcione la versión corta, pero la versión larga se rompe muy fácil, a pesar de seguir todas las instrucciones de uso (hice agujeros en la misma pieza con el método clásico: broca adecuada, luego machuelo). No sé porqué Amazon no me permite contactar al vendedor para hacerle llegar mi caso de problema de calidad.

Scritto da: Mark

Very handy, but delicate.

These work really well but you have to be VERY careful with them. You have to be sure that the drill speed is JUST right, and you hold the drill perfectly perpendicular to the drill surface. Our tech has broken a couple of these already (had for 2 weeks) in fairly light-duty use. However, when they work (and don't break!), they're fantastic.

Scritto da: Laking

So far so good

I had used a few other drill and tap bits that have broke within the first day of use. These are quick, stay sharp and save a ton of time from needing to drill a hole, then tap, then clean the hole up after it's all done

Scritto da: Alexthaman

brisé au deuxième trou

Le premier trou a été à merveille dans de l’acier 1/4 de pouce d’épais, rapide et efficace, dès le deuxième trou la mèche a cassée dans le trou occasionnant des dommages à l’acier en tentant d’extraire la mèche endommagée.

Scritto da: A. Prigojine

Great tool to make the user very time efficient on ...

Great tool to make the user very time efficient on a job requiring high volumes of tapped/drilled holes. Works well in aluminum but needs occasional cleaning of the cutting teeth to prevent damaged threads. I would love to have a metric set as well.