LMT Onsrud 63-768 Tvrdokovová upnutá špirála O drážka, palec, povrch bez povlaku (svetlá), 21 stupňová špirála, 1 drážka, celková dĺžka 2,0000, priemer rezu 0,1875, priemer stopky 0,2500 3/16 palca

Brand:LMT Onsrud

2.8/5

73.08

POPIS PRODUKTU Greenlee s hrdosťou zamestnáva zamestnancov Spojených štátov amerických v siedmich výrobných závodoch, kde navrhujeme, montujeme a vyrábame určité produkty, ktoré spĺňajú prísne požiadavky vyrobené v USA alebo kvalifikačné vyhlásenia. Odporúčame spotrebiteľom, aby si prezreli naše obaly produktov alebo marketingové materiály nachádzajúce sa na Greenlee, aby pochopili pôvod konkrétnych produktov. OD VÝROBCU Digitálny multimeter Greenlee DM-200 600 V je vybavený automatickým nastavením rozsahu pre pohodlnú obsluhu, bezkontaktnou detekciou napätia a šetrením vášho času. Údaje uchovávajú a zachytávajú merania. Automatické vypnutie a indikátor slabej batérie. Rozhranie RS-232, možno pripojiť k PC pre rozšírenú meraciu schopnosť s voliteľným opticky izolovaným rozhraním DMSC-2. Režim zobrazenia relatívneho posunu na zobrazenie relatívnych zmien meraní. Meranie frekvencie, teploty a kapacity a striedavého pracovného cyklu. Príslušenstvo obsahuje dve 1,5 V AAA batérie, testovacie káble a teplotnú sondu. Maximálne meranie napätia 6000.

Nie sú k dispozícii žiadne jednotky
Jednoduchá flauta, uhol 21 stupňov. Pri chode proti smeru hodinových ručičiek (pravý rez) špirálovito drážkované nástroje odvádzajú triesky hore a von z rezu, aby sa znížilo upchávanie. Okrúhle stopky umožňujú použitie so širokou škálou systémov upínania nástrojov. Nepovlakované nástroje majú len základný substrát bez akejkoľvek ďalšej úpravy alebo povlakov a sú vhodné pre širokú škálu aplikácií. Pevné tvrdokovové nástroje ponúkajú dlhú životnosť nástroja a vyššie rezné rýchlosti ako iné substráty, sú však krehkejšie a musia sa používať s pevnými systémami upínania nástrojov.
Country of Origin USA
Cutting Diameter 0.19 Inches
Cutting Length 0.63 Inches
Domestic Shipping Item can be shipped within U.S.
Finish Type Uncoated
Finish Type Uncoated (Bright)
International Shipping This item can be shipped to select countries outside of the U.S.
Item model number 63-768
Manufacturer LMT Onsrud
Material Carbide
Number of Flutes 1
Product Dimensions 4 x 0.5 x 0.5 inches; 0.8 Ounces

2.8

8 Review
5 Star
47
4 Star
18
3 Star
10
2 Star
9
1 Star
16

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené*

Scritto da: R. A. Jones
Nice cutter, shank is 1/4" despite the title and photo.
The title is a bit off because it says the shank is 0.125" when the specs say the shank is 1/4". The photo also shows a cutter with the shank diameter the same as the cutting diameter. It IS, however, 1/4" shank. I use it on a smallish CNC router with a 2hp spindle and it's worked quite well. In soft plastics like ABS I initially had the chip winding around the shank, melting and make a truly horrible cut. I built a new dust shoe to dramatically increase the air velocity around the cutter and with that dust shoe to keep the chips clear this cutter has worked very well.
Scritto da: Mississippi
Good bit
Nothing wrong with this one
Scritto da: Paul Haiducu
Arrived damaged!
I am not an expert in this, but the shop teacher I have worked with to drill holes in an aluminum plate tells me that the bit is damaged and cannot be used. Unfortunately, we have not carefully looked at the bit when it arrived (ordered on May 23, 2019), hence it is too late to return it or exchange it. It took the teacher a while to find time for the project I wanted done (we had the summer off, traveling, etc.). Yesterday, he realized that the bit is no good. The bit has not been used (and the shop teacher tells me that is obvious). These are not cheap, I am out almost $30.
Scritto da: Andrew D. Mowry
The description for this is incorrect. The 1/8” bit ...
The description for this is incorrect. The 1/8” bit has a 1/4” shank, not 1/8” as described and shown in the photo.
Scritto da: Seein Stripes
Great for HDPE on Bob's CNC E3
I now have about 20+ hours on the bit cutting and drilling .375" Starboard HDPE. I can say it is RAZOR sharp since it sliced my finger like a scalpel trying to remove some plastic shavings from around the bit. Runs straight and true at 45 ipm on my Bob's CNC machine.
Scritto da: Gary
This is the best bit I ever used on this material
I cut an aluminum composite material with this bit. The material is 2 aluminum skins bonded to a plastic center. This is the best bit I ever used on this material, a very clean, effortless cut.
Scritto da: Eric Varsanyi
Great cutter, clean edges on acrylic
This cuts acrylic like butter and leaves a very nice edge. I'm running a router at 18000 RPM with a feed rate of around 70 IPM and .06 depth cuts in cast acrylic.
Scritto da: bookbound93
Not 1/8 shank
Nice cutter, but needed a 1/8 shank and this is a 1/4 shank. Not happy.

Súvisiace produkty

Objavte našu medzinárodnú sieť

Dodávame do 28 krajín, viac ako 200 000 produktov. Zostaňte informovaní, prihláste sa na odber noviniek.

Array