Anderson Metals 56103-08 Mosadzná potrubná armatúra, spojka, 1/2 x 1/2 samica rúrka 1/2 x 1/2 1

Brand:Anderson Metals

3.7/5

26.48

Spojovacia potrubná armatúra Anderson Metals je vyrobená z mosadze a má vnútorné závitové spoje National Pipe Taper (NPT). Táto spojovacia armatúra spája dve rúry idúce rovnakým smerom s rovnakým priemerom, aby sa predĺžila priama trasa. Má vnútorné závity NPT na pripojenie k rúram s vonkajším závitom, čím vytvára tesnejšie tesnenie ako priame závity. Táto armatúra je vyrobená z mosadze pre odolnosť proti korózii, ťažnosť pri vysokých teplotách a nízku magnetickú permeabilitu. Mosadz môže byť spojená s meďou, mosadzou, plastom, hliníkom a zváranou oceľou. Prevádzkové teploty pre túto armatúru sa pohybujú od -53 do 121 stupňov C (-65 až 250 stupňov F). Táto armatúra spĺňa špecifikácie B16 Americkej spoločnosti pre testovanie a materiály (ASTM) B584 a Americkej spoločnosti strojných inžinierov (ASME)/Amerického národného inštitútu pre normy (ANSI) B16 na zabezpečenie kvality. Potrubné armatúry sú komponenty používané na pripojenie, ukončenie, riadenie prietoku a zmena smeru potrubia v mnohých rôznych priemyselných odvetviach. Pri nákupe potrubných tvaroviek zvážte použitie, pretože to ovplyvní typ materiálu, tvar, veľkosť a požadovanú trvanlivosť. Armatúry sú dostupné so závitom alebo bez závitu, v mnohých tvaroch, štýloch, veľkostiach a plánoch (hrúbka steny potrubia). Anderson Metals vyrába mosadzné fitingy, ventily a potrubné vsuvky. Spoločnosť založená v roku 1951 má sídlo v Kansas City, MO.

Tieto armatúry obsahujú olovo a federálny zákon ich nepovoľuje inštalovať na pitnú vodu v USA a na ich územiach. Spĺňa špecifikácie ASTM B584 a ASME/ANSI B16 pre zabezpečenie kvality. Prevádzkové teploty sa pohybujú od -53 do 121 stupňov C (-65 až 250 stupňov F). Mosadz pre odolnosť proti korózii, ťažnosť pri vysokých teplotách a nízku magnetickú permeabilitu. Závity National Pipe Taper (NPT) na pripojenie k rúram s vonkajším závitom. ID ½” spojky by bolo blízko ¾”. Spojka na spojenie dvoch rúr s rovnakým priemerom v priamom smere.
Brand Anderson Metals
Color Brass
Connector Type Coupling
Country of Origin USA
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Brass
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 1 x 1 x 1 inches
Item model number 56103-08
Manufacturer Anderson Metals
Material Brass
Number of Pieces 2
Product Dimensions 1 x 1 x 1 inches; 1.13 Ounces
Size 1/2" x 1/2"
Thread Type NPT

3.7

13 Review
5 Star
80
4 Star
12
3 Star
5
2 Star
1
1 Star
3

Napíšte svoju recenziu

Váš email nebude zverejnený. Všetky povinné polia sú označené*

Scritto da: Snide
3/4 x 3/4 female coupler perfect
purchased one. it arrived one day earlier then stated, was in perfect shape, and fit my 3/4" male pipe perfect. so i ordered two more. they also arrived earlier than stated. thank you.
Scritto da: Amazon Customer
quality parts
Excellent price, quality and delivery
Scritto da: Thomas D. Kehoe
Not for 1/4" outside diameter (O.D.) compression fitting
I got perplexed installing a water hammer arrestor. The water hammer arrestor was labeled "1/4" O.D." But its male fittings were 1/4" inside diameter (I.D.). I couldn't understand why this 1/4" I.D. female coupler slid over the male fittings. The male fittings were 0.43" and this female couple is 0.455". After spending way too much time searching on the Internet I put on my mask and went to Home Depot. The plumbing aisle employee told me that the water hammer arrestor had a compression fitting. I went home and found a YouTube video explaining how to connect compression fittings. Twenty minutes later I'd installed my water hammer arrestor, with no extra parts. So I never used this brass coupler but it looks nice. :-) My pipe is 0.25" inside diameter and the outside diameter of the male threads are 0.43". This coupling has an inside diameter of the female threads of 0.44". It slides right over my pipe without engaging. Apparently there are different plumbing "standards" where "1/4-inch" means different sizes. The specs should say what the diameter of the threads are and what pipe it threads onto.
Scritto da: James Barr
Needed For A Propane Quick Connection
I purchased a propane quick connect hose, and then discovered I could not connect to a LPG generator from a 5th Wheel quick connect outlet. This double female coupling allowed me to make the connection. I removed the safety quick connect valve, installed the coupling, and attached a 1/4 inch male quick connection, which I inserted into the generator safety coupling valve. Difficult to find on Amazon, and local hardware stores were clueless on LP quick connections.
Scritto da: Dale Williams
Great products! You will not be disappointed.
I had to make an extension pipe for a propane manifold. This coupler saved the day! The hex nut fittings they make are 2nd to none. I have been using Anderson Metals products for quite awhile now. I have never had one fail! I recommend these to anyone that has a plumbing job.
Scritto da: victor neal
Perfect fit
Item worked perfectly
Scritto da: Rvrguyd
1/4" pipe coupling
The 1/4" is the inside hole diameter. The outside diameter is about 3/8". The threads on one end got a little smashed and threading the pipe on it was a challenge but I got it to fit since brass is soft enough to work with so long as you don't cross thread it.
Scritto da: K. Matsinger
Brass fitting for shower
Need new Brass fitting or my updated walk in shower, local Ace said be hard to find what I needed but Amazon it on Amazon it was perfect. GRACIAS!
Scritto da: Mar co
this is not for shower
i bought this one but this is not for shower (its hard to find female to female pipe ends) inside theres no stopper for the rubber. inside is a straight hole. i still try to put 2 round rubbers inside. and put lots of teflon tape on the male pipe. its ok but theres leak but not too much.
Scritto da: Robert L.
Works for Air Compressor, Air Hose Adapter, Water Separator / filter Connections
I'm using this to connect my air compressor with my air separator or hose adapter and it works very well. Material is good, not flimsy. Also air tight, no leakage for me and I'm not using Teflon tape.
Scritto da: Bruce H
Thin walled.
I used it as a connection between air hoses. The thickness of the wall is a bit thin. One I had before split after a year.
Scritto da: Cloud Morrish
It’s a brass pipe…
It is what it is. A brass pipe coupler. It does the job it was made to do.
Scritto da: Shining star
Shipped wrong item waste of time
Order a 1/4” and got sent 3/8”…!!! Disappointed as it was such a waste of my time waiting for this to arrive!!!!

Súvisiace produkty

Objavte našu medzinárodnú sieť

Dodávame do 28 krajín, viac ako 200 000 produktov. Zostaňte informovaní, prihláste sa na odber noviniek.

Array